とりあえずVer.2.13までのお話で。
今後のVer.Upで変わるかもしれませんので要確認。
選択可能単位は『g』『kg』……未記入の場合『g』とされます。
さて、この項目を使用する際の注意事項を挙げてみましょう。
・子部品にのみ適用可能(製品データには適用できない)
■ g←ココに適用できない
├■ kg
└■ g
・材料には適用できない
■ g
├■ g
│├● g
│└● g
└■ kg
├● g
└● g
例によって例の如く実際に再現してみました。
"C","Ver.2.13","2011/06/16","正常終了","","EXLIST-2011-06-01JP.xls"
"H","","","","",""
"D","1","dummy","dummy","3","","","1","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","",""
"D","2","dummy","dummy","","","","2","dummy1","dummy1","1","1","","Iron/Other Iron alloy (Unalloyed, low alloyed)","","1","JAMAA4444","FE1","","1.1.1","1","","","","7439-89-6","Iron","100","","0","0","0","0","","","","","","","","","","","","","","","","1762",""
"D","3","dummy","dummy","","","","2","dummy2","dummy2","0.001","2","","Iron/Other Iron alloy (Unalloyed, low alloyed)","","1","JAMAA4444","FE2","","1.1.1","1","","","","7439-89-6","Iron","100","","0","0","0","0","","","","","","","","kg","","","","","","","","1762",""
上の"C"からの文字列をtxtファイルに貼り付けて"C"・"H"・"D"で始まる5行に整形して保存→拡張子をcsvに変更してJAMAシートで取り込めます。
■dummy(3g)
├■dummy1(1g)*1
│└●FE1(1g)
└■dummy2(0.001kg)*2
└●FE2(1g)
って構成なんですが、結果として構成中の子部品のみにしか適用できないわけです。
製品質量:g(固定)
構成部品質量:g or kg
材料質量:g(固定)
何がやりたいのかさっぱりわかりません。
コレって使い道あるのか?
今後のVer.Upで変わるかもしれませんので要確認。
選択可能単位は『g』『kg』……未記入の場合『g』とされます。
さて、この項目を使用する際の注意事項を挙げてみましょう。
・子部品にのみ適用可能(製品データには適用できない)
■ g←ココに適用できない
├■ kg
└■ g
・材料には適用できない
■ g
├■ g
│├● g
│└● g
└■ kg
├● g
└● g
例によって例の如く実際に再現してみました。
"C","Ver.2.13","2011/06/16","正常終了","","EXLIST-2011-06-01JP.xls"
"H","","","","",""
"D","1","dummy","dummy","3","","","1","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","","",""
"D","2","dummy","dummy","","","","2","dummy1","dummy1","1","1","","Iron/Other Iron alloy (Unalloyed, low alloyed)","","1","JAMAA4444","FE1","","1.1.1","1","","","","7439-89-6","Iron","100","","0","0","0","0","","","","","","","","","","","","","","","","1762",""
"D","3","dummy","dummy","","","","2","dummy2","dummy2","0.001","2","","Iron/Other Iron alloy (Unalloyed, low alloyed)","","1","JAMAA4444","FE2","","1.1.1","1","","","","7439-89-6","Iron","100","","0","0","0","0","","","","","","","","kg","","","","","","","","1762",""
上の"C"からの文字列をtxtファイルに貼り付けて"C"・"H"・"D"で始まる5行に整形して保存→拡張子をcsvに変更してJAMAシートで取り込めます。
■dummy(3g)
├■dummy1(1g)*1
│└●FE1(1g)
└■dummy2(0.001kg)*2
└●FE2(1g)
って構成なんですが、結果として構成中の子部品のみにしか適用できないわけです。
製品質量:g(固定)
構成部品質量:g or kg
材料質量:g(固定)
何がやりたいのかさっぱりわかりません。
コレって使い道あるのか?
環境報告・IMDS・JAMAシートにお困りなら株式会社シンク・リードへご相談ください。
環境報告実務駆け込み寺で公開中の知識と経験で御社のサポートをします!
環境報告実務駆け込み寺で公開中の知識と経験で御社のサポートをします!
投票数:121
平均点:4.63
JAMAシートで収集したデータの管理 |
JAMAシートについて |
項目番号40(AP列)『構成部品数量単位』について考える |